Every electrician has opened a panel door and found a directory that says "lights," "plugs," "kitchen?" and the name of a kid who moved out in 2009. Or nothing at all. The customer has no idea that is a problem until a breaker trips at ten at night and they are in the basement with a flashlight, flipping things one at a time.

Tracing and labeling a panel is real work, it is easy to sell, and most guys either never offer it or throw it in for free at the end of another job. Here is how to price it like the rest of your work.

Why it is a real job

NEC 408.4(A) wants every circuit identified clearly enough that you can tell it apart from every other circuit, with spares marked as spares, and it does not let you use descriptions that depend on who lives there. "Bobby's room" stops meaning anything the day Bobby moves out. The 408.4 guide covers the exact requirements.

Home inspectors often note a missing or vague directory, so buyers and sellers show up already knowing they need it fixed. Landlords want it so a tenant can reset a breaker without calling anybody. And every homeowner wants it the one night they need it.

What the hours cover

  1. Walk the house first. Every room, every receptacle, every light, every hardwired appliance, written on a rough floor plan before you touch a breaker.
  2. Tell the customer what is going to go off. The fridge, the sump pump, the garage door, the computer somebody is working on, anything medical. Get the okay before you kill anything.
  3. Trace. A plug-in breaker finder gets you most of the receptacles with the power on. Lights and hardwired loads you confirm one breaker at a time.
  4. Write the directory. Room and load, specific enough that a stranger could find the circuit. Spares marked as spares. Typed, not handwritten.
  5. Test and hand it over. Walk the customer through it and point out anything you found that needs fixing.

On a typical house with a decent tracer, figure a few minutes a circuit plus the walk-through. Basements full of boxes, finished additions and shared neutrals all run long. Time your next three and use your own number.

The price, worked out

Same formula as every flat rate calculator on this site, at the electrical book numbers: a $135 loaded rate, a 1.35 overhead multiplier and a 20 percent target margin, which makes a labor factor of 1.69, and 30 percent on material. Material here is the label stock, the directory card and the sleeve.

JobGoodBetterBest
Directory rewrite only, circuits already known
0.5 hrs, $10 material
$130$160$200
Trace and label, up to 24 circuits
2 hrs, $15 material
$480$590$740
Trace and label, 25 to 42 circuits
3 hrs, $20 material
$710$890$1,100

Take the middle line. Two hours at $135 with a 1.69 factor is $455.63 of labor. $15 of material with 30 percent on it is $19.50. Together that is $475.13, which rounds to $480. Better is the Good price times 1.25 and Best is times 1.55, each rounded the same way.

What changes between the tiers

  • Good. Every circuit traced, a typed directory in the door, spares marked.
  • Better. All of that, plus labels on the breaker handles and a room-by-room map so the customer can find the circuit for any outlet in the house.
  • Best. All of that, plus a copy of the schedule and the map for the homeowner's binder, a photo of the panel, and a written list of anything you found, like double taps or open knockouts, with a price to fix each one.

The Best tier sells itself to the right customer, and it tends to sell your next job too. A homeowner holding a written list of what is wrong with their panel, with a price next to each item, usually calls the guy who wrote it.

At your rate

Job, Good tier$110 rate$135 rate$165 rate
Directory rewrite only$110$130$150
Trace and label, up to 24 circuits$390$480$580
Trace and label, 25 to 42 circuits$580$710$860

This is almost all labor, so it moves with your rate more than nearly anything else you sell.

When to sell it

  • Any service call where you had to flip breakers to find the circuit. You just proved the directory is wrong. Tell them what it costs to fix while you are standing there.
  • Before a house goes on the market, or after the inspection. A vague directory on the inspection report is an easy job to schedule.
  • Rentals. A landlord who gets a call every time a tenant trips a breaker will pay to stop getting that call.
  • Not on your own panel swaps. If you are replacing the panel or doing a service upgrade, labeling every circuit is already part of that job. Do not charge for it twice.

Do the paperwork right

A typed schedule that fits the door pocket looks like you know what you are doing. The free panel schedule template prints to fit standard Square D, Eaton, Siemens and GE residential panels, and this guide covers numbering, multiwire circuits and the difference between a spare and a space.

For the Best tier, add a branded leave-behind with your company name and number on every page. Put the schedule and the room map in it, and your number is on the shelf the next time something goes wrong.

The directory is the one part of the panel the customer actually reads. Make it right, charge for it like the rest of your work, and you are the electrician whose name they find when they open that door.

Frequently Asked Questions

How much should an electrician charge to label a panel?
At a $135 loaded rate with overhead and margin built in, tracing and labeling a panel of up to 24 circuits is about two hours and prices at $480 for the Good tier. Rewriting a directory when the circuits are already known is about $130. Bigger panels take longer and cost more.
How long does it take to trace every circuit in a house?
On a typical house with a plug-in breaker finder, figure a few minutes a circuit plus the walk-through, so two to three hours for most residential panels. Cluttered basements, additions and shared neutrals take longer.
Does the NEC require a panel directory?
NEC 408.4(A) requires every circuit to be clearly identified by its specific purpose, with spare positions marked, and the description cannot depend on who happens to be living there. Check which edition your jurisdiction has adopted.
Can you trace circuits with the power on?
A plug-in breaker finder works with the power on and lets you leave the dead front in place. Lights and hardwired loads usually get confirmed by turning breakers off one at a time, with the customer's okay. If the cover has to come off, treat it as energized work.